24/7 DispatchColorado Springs & Pikes Peak Region
Troubleshooting

Rinnai Error Code 10, 11, and 12: Flame Rod & Gas Pressure Diagnosis

Factory-Certified Technician
•
August 30, 2026
•
7 min read
Rinnai Error Code 10, 11, and 12: Flame Rod & Gas Pressure Diagnosis
Key Takeaways for Homeowners
  • Code 10 is airflow obstruction (snow, bird nests, lint, or incorrect fan speed).
  • Code 11 is failure to light initially (gas valves, igniter gap, low gas pressure).
  • Code 12 is flame loss during run, most often caused by a dirty flame ionization rod.
  • Never use coarse sandpaper on flame rods; use OEM cleaning procedures to avoid sensor damage.

Rinnai is known throughout the plumbing trade for exceptional engineering and longevity. Their SENSEI series (including RU199i and RUR199i) delivers outstanding performance in cold climates. However, when an operational disruption occurs, the digital MC-91 temperature controller will flash an alert code. In Colorado Springs, three codes account for over 70% of Rinnai service calls: Code 10, Code 11, and Code 12.

Decoding Rinnai Code 10: Air Flow / Venting Restriction

Rinnai Error Code 10 indicates an Air Flow Problem. The unit's electronic combustion fan is failing to move the designated volume of air, or the exhaust vent backpressure sensor has detected abnormal resistance.

Common causes in Colorado Springs include:

• Snow or Ice Drift: In Monument and Black Forest, heavy snow drifts frequently block horizontal side-wall vent terminations.

• Insect or Bird Nests: In spring and summer, wasps and birds build nests inside the unshielded intake pipes.

• Clogged Blower Fan: The internal fan wheel accumulates pet hair, laundry lint, and basement dust, slowing down its rotation speed.

• Altitude Misconfiguration: Rinnai units feature dip switches to compensate for long vent runs and high altitudes. If set incorrectly, Code 10 will flash.

Decoding Rinnai Code 11: No Ignition

Error Code 11 occurs when there is No Ignition. The water heater received a demand signal from the flow sensor, the fan began spinning, and the igniter clicked, but the flame never caught on the burner.

Diagnostic checklist for Code 11:

1. Gas Valve Shutoff: Confirm the yellow gas handle beneath the unit is parallel to the pipe. Check if Colorado Springs Utilities performed nearby gas main maintenance.

2. Igniter Electrode Gap: The high-voltage spark gap between the two ceramic igniters must measure exactly 3.5mm to 4.5mm. At high elevation, even a minor deviation prevents gas ignition.

3. Low Gas Supply Pressure: Natural gas units require 3.5 to 10.5 in. W.C. Propane units require 8.0 to 13.5 in. W.C. A digital manometer test under full fire is required to verify pressure.

Technician Tip: If you hear a loud 'thump' or mini-explosion before Code 11 flashes, shut off the gas valve immediately! This indicates delayed ignition due to misaligned spark electrodes.

Decoding Rinnai Code 12: Flame Failure During Run

Unlike Code 11, Error Code 12 means the flame lit successfully, but then extinguished during active heating.

By far the most common cause of Code 12 in the Pikes Peak region is a fouled flame rod sensor. The flame rod is a thin metal probe immersed in the burner flame. It uses the physical phenomenon of flame rectification to confirm a healthy flame. When coated in white silica deposits from Front Range water vapor, the sensor loses electrical continuity, prompting the control board to instantly kill the gas supply as a safety precaution.

Cleaning vs Replacing Rinnai Flame Sensors

In many cases, an experienced technician can restore a Rinnai unit by carefully removing the combustion inspection plate and polishing the flame rod and igniter pins with ultra-fine Scotch-Brite abrasive pad or 600-grit emery cloth.

However, if the ceramic insulator around the rod is hairline-cracked, moisture can cause high-voltage electrical leakage to ground. In that scenario, replacing the complete flame rod assembly is the only lasting fix.

Conclusion & Professional Recommendations

Don't spend another day taking cold showers. If your Rinnai controller displays Code 10, 11, or 12, call our Colorado Springs team to dispatch a factory-trained Rinnai repair technician.

Direct Phone Dispatch Only • Zero Lead Forms

Need Diagnostic Help on Your Tankless System?

Call our local Colorado Springs dispatch line. No waiting for email or form replies—speak directly with an on-call technician.

What Callers Should Have Ready For Fast Diagnosis:

Brand & Model: Printed on front panel (Navien, Rinnai, Noritz, etc.)
Error Code: Flashing letters/numbers (e.g. E003, Code 11, 90)
Fuel Type: Natural Gas (CSU), Propane (LP tank), or Electric (240V)
Home Address: Colorado Springs, Monument, Fountain, or nearby ZIP code
24/7 Priority Hotline(456) 789-0123Call For Immediate Dispatch
Licensed & Insured Local Professionals

Continue Reading

View All 10 Guides →
Troubleshooting

Navien Error Code 003 vs 012: Ignition Troubleshooting in Colorado Springs

Waking up to cold water and a flashing E003 or E012 error on your Navien tankless display? Here is an expert breakdown of why these ignition faults happen at high elevation and how to resolve them safely.

Read Article
Technical Guide

Why Tankless Water Heaters Need Altitude Derating Above 6,000 Feet

Planning or troubleshooting a tankless water heater along the Colorado Front Range? Learn why atmospheric derating above 6,000 feet changes gas sizing, flow capacity, and combustion safety.

Read Article
Maintenance

Colorado Springs Hard Water Guide: How Mineral Scale Destroys Heat Exchangers

Discover why Colorado Springs water chemistry accelerates heat exchanger calcification, how to recognize early signs of scale restriction, and the best preventative solutions.

Read Article
Techs On Call Now
Colorado Springs Dispatch
Call (456) 789-0123